top of page

This product has been discontinued

 

FFA Generation 2 DSP 4 channel amplifiers feature powerful digital signal processing (DSP). The DSP controlled amplifier provides a cost effective solution for sound system design and can be used for installation or temporary sound systems or any high quality amplified audio requirement. The system is controlled by software called FATWARE. The software is intuitive to use and offer the user a toolbox of audio functions to allow many different systems to be designed.

 

The FFA-4004 G2 DSP amplifier has 4 analogue audio input’s which can be switched to allow connection of AES/EBU signals. Unusually there are 6 audio output channels, 4 assigned to the four channels within the amplifier and 2 aux outputs connected to a pair of male XLR connectors on the rear of the amplifier. These extra processed outputs can be used to drive any other amplifier channels in the system design.

 

Complex systems can be designed and signals can be routed as required with a signal matrix.

 

The DSP has powerful dynamics processors which have fully specified compressor/limiters on each audio input. These could be used for system protection against overdrive and also for environmental noise considerations.  Each input and output has 2 bands of dynamic EQ in addtion to parametric eq on each input and output.

 

The DSP is accessed via an Ethercon connector on the rear panel of the amplifier and connected using a CAT5 Ethernet cable direct to a personal computer or via an Ethernet Hub or router. The DSP is password protected and allows the designer to keep interference from unauthorised persons whom may change parameters and either damage the loudspeaker system or exceed set environmental noise levels.

 

Features at a glance


  •  4 x 1000 Watts @ 4 Ohms

  • compressor limiter on each input

  • 6 band parametric EQ per input, 8 band parametric per output, low/high shelving, bell, notch filters, phase, band pass

  • 2 band dynamic EQ input and output

  •  Audio input and compressor/limiter

  • loudspeaker signal limiting

  •  cross over filter types 6,12,18,24,48 dB per octave But, Bes, LR

  •  Delay - up to 2 seconds, (feet, inch, mm, meters, millisecond).

  •  4 audio inputs,  6 audio outputs.

  • AES/EBU digital input selectable by a switch on the rear panel

  •   Ethernet network 

  • DSP defeat switch so that the amplifier easily reverts back to a 4 input analogue amplifier.

  •  Front panel level trim using analogue potentiometer, front panel LED signal potentiometers

  •  

Suitable Applications

 

Used to drive small - medium full range and dedicated bass loudspeakers, for touring or installation, ideal for components within touring loudspeakers such as mid range and HF, 4 Ohm drive.

 

Small full range loudspeaker for example 5”-10” + 1” driver compliment, smaller bass units 8” -10” drivers

 

High power mid range and HF drivers in multi way installed sound or touring sound systems Smaller stage monitors bi amp or full range. Use in conjuction with high power bass amplifiers signal driven from auxillary outputs on rear of DSP amplifier.

 

FFA-4004 G2 DSP Power Amplifier

SKU: GDSFFAG24004
£3,486.00 Regular Price
£3,186.00Sale Price
Out of Stock
  • Power

    Ratings

    FFA - 4004 DSP - 4 x 650 8 Ohm, 4 x 1000W 4 Ohm
     
    Gain 32 dB
    THD Typical 0.05 4 Ohm 1kHz THD+N

    Frequency

    Response

    20Hz - 20kHz +- 0.5dB
    Controls 40 Point Potentiometer per channel, power on switch
    Indicators signal green = -20dB, signal yellow = -3dB, red signal = clip, signal red protect = over current, low AC mains or 3 sec. mute on power up

    Load

    Protection

    DC on output, side chain TCA clip limiter circuit

    Amplifier

    Protection

    Short circuit, current overload, thermal shutdown, high frequency stability circuit

    Audio Signal

    Inputs

    Balanced Neutrik® Female XLR input connected Pin 1 - GND, Pin 2 - Hot +, Pin 3 - Cold - . XLR Male signal throughput each channel

    Audio Signal

    Outputs

    Neutrik® speakON each channel. Channels 1 and 3 output speakON utilises 2+ and 2- connection to allow use of 4 core loudspeaker cable for bi amp loudspeaker system for example stage monitor system

    Power

    Requirement

    1 x Neutrik® 20A powerCON connector 1 x 16A 230 VAC Circuit. Power range 185V-230VAC

    120V (configured at factory)

    System

    Cooling

    High CFM 80mm fan with proportional signal speed control. Rear to front airflow
    Dimensions 88mm Height x 483mm Width x 510mm Depth. Includes rear rack support. 19" rack mount enclosure
    Weight                                                                                  10 kg

PRICES EXCLUDE VAT

Product Rating

average rating is 3 out of 5, based on 150 votes, Product review(s)

There are no reviews yet, be the first!

Thanks for submitting a review! 😘

Add Review

Customer Reviews

LOAD MORE

Related Products

bottom of page