F Series amplifiers are made for Funktion One by English amplifier designers and manufacturers Full Fat Audio (FFA).  The five amplifiers in the range are the excellent high power F100-2 dual power supply amplifier (suited to operating into 2 Ohm loads) and four four-channel amplifiers (F20Q, F40Q, F60Q and F80Q).  The new F20Q is useful for powering distributed systems of small loudspeakers such as the F55 or F81. 
 
The F80Q's new electronic design makes it especially suited to powering the Evo 6 and 7 range with exceptional audio quality. 

All five amplifiers utilise rugged switch modulation power supplies (SMPS) with Class D Pulse Width Modulation amplifier stages.
 
The four channel models are also avaliable with internal DSP. Networking, four inputs and six outputs (four via amplifier channels and two via additional signal channels) and intuitive software offer great flexibility for both live and installation. See the DSP product versions in store or just message us.
 
Features:
High efficiency FFA Class D technology
Optional DSP card (4 channel models only)
Rugged tour class Aluminium construction
Lightweight
Side chain TCA clip limiter
Signal link connectors
Hand built and designed in England
New F20Q and F80Q now available
 
F20Q Four Channel Amplifier:
Output power (Watts RMS) per channel
8Ω - 250W; 4Ω - 500W; 2Ω - 1000W
 
F40Q Four Channel Amplifier:
Output power (Watts RMS) per channel
8Ω - 600W; 4Ω - 1000W  
 
F60Q Four Channel Amplifier:
Output power (Watts RMS) per channel
8Ω - 800W; 4Ω - 1500W  
 
F80Q Four Channel Amplifier:
Output power (Watts RMS) per channel
8Ω - 1000W; 4Ω - 2000W  
 
F100-2 Two Channel Amplifier:
Output power (Watts RMS) per channel
8Ω - 1500W; 4Ω - 3000W; 2Ω - 5000W
 
Other FFA amplifiers can be supplied on request
 
Technical Specifications  
Gain: 32dB
THD: Typical 0.05% @ 4Ohm, 1kHz THD+N  
Frequency Response: 20Hz - 20kHz ±0.5dB
Controls: 40 point potentiometer per channel, power on switch  
Indicators: signal green = -20dB, signal yellow = -3dB, red signal = clip, signal red protect = over current, low AC mains or 3 sec. mute on power up
Load Protection: DC on output, side chain TCA clip limiter circuit
Amplifier Protection: Short circuit, current overload, thermal shutdown, high frequency stability circuit  
Audio Signal Inputs: Balanced Neutrik® Female XLR input connected Pin 1 - GND, Pin 2 - Hot, Pin 3 - Cold, XLR Male signal throughout each channel
Audio Signal Outputs: Neutrik® speakON each channel. Channels 1 & 3 output speakON utilises 2+ and 2- connection to allow use of 4 core loudspeaker cable for bi amp loudspeaker system, for example stage monitor system.  
Power Requirement: 1 x Neutrik® 20A powerCON connector, 2 x 16A 240V VAC circuit. Power range 185V-240V AC  
System Cooling: High CFM 80mm fan with proportional signal speed control. Rear to front airflow.
 
Dimensions: 483mm x 510mm x 88mm. Includes rear rack support. 19'' rack mount enclosure
Weight: 9kg (F40Q & F60Q); 12kg (F100-2)
 
N.B. Please note that the F-Series amplifiers have an opposite airflow to that of the E-Series amplifiers and therefore, when used together in a rack it is advisable to place the F-Series at the top of the rack.